Calculadora de Rodapé

Última atualização: 2026-06-23

Use a Calculadora de Rodapé para obter resultados precisos. Insira os valores abaixo.
Dados
Resultado
Insira os valores e pressione Calcular
Common Sizes — Click to Fill
Perímetro do quarto (m) Número de portas (pcs) Comprimento da tábua (m) Largura da porta (m)
Small door 9 m 1 pcs 2.4 m 0.9 m
Standard door 13.5 m 2 pcs 2.4 m 0.9 m
Large door 18 m 2 pcs 2.4 m 0.9 m
Window 27 m 3 pcs 2.4 m 0.9 m
Bay window 36 m 4 pcs 2.4 m 0.9 m
Ferramentas relacionadas
Calculadora de Moldura de Teto Calculadora de Deck Calculadora de Piso Laminado Calculadora de Janelas Alumínio/PVC

O que é o Baseboard Calculator?

Baseboards (skirting boards) run along every wall at floor level — calculating the right linear metres means measuring the full room perimeter, subtracting door openings, and adding waste for mitre cuts at corners. Get it wrong and you'll have visible joins or run short mid-room.

You may also find the Crown Molding Calculator, Decking Calculator, and Laminate Flooring Calculator useful.

Quem usa esta calculadora?

This tool is used by homeowners finishing a renovation, carpenters quoting trim work, and builders specifying finish materials.

Como usar the Baseboard Calculator

  1. Insira Room perimeter.
  2. Insira Door width.
  3. Insira Number of doors.
  4. Insira Board length.
  5. Clique em Calcular para ver os resultados instantaneamente.

Fórmula

The calculator uses the following formula:

Net perimeter = room_perimeter - (doors × door_width); Boards = ceil(net_perimeter × 1.05 ÷ board_length)

Exemplo de cálculo

A 5 m × 4 m room with two 0.9 m door openings needs (18 - 1.8) × 1.05 = 17 linear metres of baseboard allowing for waste.

Cálculo passo a passo

  1. Gross perimeter: 18 m
  2. Subtract door openings: 2 × 0.9 m = 1.8 m → 16.2 m net
  3. Add 5% for cuts: 16.2 × 1.05 = 17.01 m
  4. Boards (2.4 m each): ceil(17.01 ÷ 2.4) = 8 boards

Erros comuns a evitar

  • Including door openings in the perimeter instead of subtracting them
  • Forgetting to account for inside corners where boards meet
  • Not allowing for end cuts — the offcut from one wall can often start the next
Pro Tip: For painted baseboards, MDF is cheaper and machines perfectly. For stained or clear-coated wood, use solid timber or finger-jointed pine. Always prime MDF cut ends — they absorb paint and swell if left unprimed.

Perguntas frequentes

How do I measure baseboard for a room?
Measure the perimeter of each wall, subtract all door openings (measure between door jambs), then add 5–10% for mitre cuts at corners and waste. This calculator does all of that automatically.

What height baseboard should I use?
70–90 mm is standard for rooms with 2.4 m ceilings. Use taller baseboards (100–140 mm) in rooms with higher ceilings to maintain visual proportion. Very tall ceilings (3 m+) can use 150 mm or taller profiles.

Should baseboard be installed before or after flooring?
Hard flooring (tile, timber, laminate) should be installed first, then baseboard on top to cover the expansion gap. Carpet is typically laid after baseboard, with the carpet tucked under the board.

How do I deal with out-of-square corners?
Most corners are not exactly 90 degrees. Use an angle finder or digital protractor to measure the actual angle, then divide by 2 for each mitre cut. Small gaps can be filled with caulk and painted.

Can I use flexible baseboard for curved walls?
Yes — thin MDF baseboard (6–9 mm) can be bent around gentle curves with a heat gun or by scoring the back. For tight curves, use purpose-made flexible trim or build up the curve with multiple layers of thin strips.

Escrito e revisado pela equipe editorial do CalcToWork. Última atualização: 2026-06-23.

calcto.work — Calculated on 2026-06-23